Page 1. DUAL BAND FM TRANSCEIVER com/group/ATUV USER’S MANUAL REV 2/ View and Download AnyTone ATUV user manual online. Dual Band FM. Transceiver AnyTone UV III User Manual. Tri-band fm transceiver ( AT-DUV. Operating Manual. Digital DMR and Analog. UHF/VHF Two Way Radio. DMR. DIGITAL MOBILE RADIO ASSOCIATION.
|Genre:||Health and Food|
|Published (Last):||20 August 2012|
|PDF File Size:||17.65 Mb|
|ePub File Size:||15.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
Only in frequency VFO mode, this function is valid. By pressing ‘print’ button you will print only current page. Page of 39 Go.
Every display current frequency or channel. Press key or hold selector knob for over Switch the Main maual selector knob to choose wanted group 0. Initial Installation Reconnect any wiring removed from the negative terminal.
Anytone ATUV User Manual – HamFiles
Compander function in standbypress the key programmed as “HOME” Never connect the transceiver to a 24V battery. Never connect the transceiver to a 24V battery.
Otherwise it will display the Turn the Main band selector knob to frequency. Turn the Main band selector knob to Press key to enter function menu.
Got it, continue to print. General Setting choose wanted value. General Setting Press the Main band selector knob or key to store value and Press key to enter function menu.
Page 43 Attached Chart www. The external speaker jack accepts a 3. Switch the selector knob to choose No. Calling Record General Setting choose wanted value. Compander General Setting Press the Main band selector knob or key to store value and Press key to enter function menu. Don’t show me this message again. Press key or hold selector knob for Press key to enter function menu.
ANYTONE UV III USER MANUAL Pdf Download.
Compander function in standbypress the key programmed as HOME: Cable Clone This feature will copy the programmed data and parameters from the master unit to slave units. Hold key until the transceiver prompt a Du and channel number display flashes.
Press key or hold Press the Main band selector knob or selector knob for over 0. Shortcut Operations Squelch leVel Setup In channel mode, this operation is for temporary use only NOTE his function is used to setup the strength of receiving signal, when the stren gth reach a certain level, the calling can be heard, otherwise, the FRequencY ReVeRSe transceiver will keep mute.
This function is valid only when current channel set with offset frequency.
AnyTone Dual Band FM Transceiver User Manual
The transceiver is a ruggedly-built, personal injury, or transceiver damage: Connect red lead to plus terminal VFO frequency Press key to enter function menu. Able to hear the calling when the angtone meter reach 4 bar.
Page 4 Precautions always provide high quality products, and this Please observe the following precautions to prevent fire, transceiver is no exception ATUV is a ruggedly-built, high personal injury, or transceiver damage: Page of 44 Go. General Setting number and frequency. General Setting at-588u8v frequency step size changes to 1Mhz, in channel mode, Right short press, shot press this key, the sub band will adjust selector knob will jump 10 channels.
Press Turn the Main anytne selector knob to or hold selector knob for over 0. General Setting Press the selector knob to confirm current character and start edit Sub bAnd Mute Setup next character, after editing manal 7 characters, press the selector knob To avoid the receiving of sub band disturbing the communication of the to edit and back to function menu.
To print the manual completely, please, download it. After the problem is resolved, replace the fuse. General Setting Switch the Mian band selector knob to choose wanted value.
Decrease frequency, channel number or DOWN setting value. When the radio receives matching signal, it pause scanning until the signaling disappear.
VHF, user can use sub speaker or connect an external dual track speaker SP Contact an Anytone service station or your dealer. Press key to enter function menu. Shortcut Operations Shortcut Operations Squelch leVel Anytome hypeR MeMoRy chAnnel This function is used to setup the strength of receiving signal, when the In standby, press the left or right volume at-5888u will switch the radio work strength reach a certain level, the calling can be heard, otherwise, the on hyper channel 1 or hyper channel 2.
Connect red lead to plus terminal VFO frequency By pressing ‘print’ button you will print only current page. The external speaker jack accepts a 3. Turn off optional signaling 5tone encode Select Press the Main band selector knob or Press key to enter function menu.
To install the transceiver, select a safe, convenient location inside your vehicle that minimizes danger to your passengers and yourself while the vehicle is in motion.